Showing posts with label DIY. Show all posts
Showing posts with label DIY. Show all posts

Thursday, March 4, 2010

Fork Oil Change. It's a... SNAP!

So, I've got the top yoke in my hand, and I sit with it wondering what to do as if by some benevolent act of grace from the Motorcycle Gods, it will be made right again.  Snapping the left side pinch bolt off and leaving the threads in my 'unobtainium alloy' yoke isn't quite what I anticipated dealing with as I set out to "just change my fork oil".

Can of worms?  Hmmm.  Pandora's Box?  Well, I guess it was all that!

I'm at 58K on the clock now with my 1995 Trident , about 12K put on since I bought it last July.  So I'm looking at 12K service interval items, and I decide it's time to look at the front forks.  I have no idea what's in there, one of the PO's had already made a lot of mods, so the forks could have titanium springs in them for all I know!  At the very least I'll change the fork oil.

I began by loosening the dust caps on the tops of the forks.  Then I removed the pinch bolts on the upper and lower yokes of the triple tree.  The upper left's a little tight, thus the predicament I describe above.  The forks slide out nice and easy.  I unscrewed the caps, dumped the old stinky fork oil out, and pumped them a few times.  I lifted the dust seals and inspected the fork seals as well.


As I drop the springs out through my now inverted forks, I notice that these are strange looking springs: they're only about 12-1/2" long constant rate coils, and have 10"spacers!  I didn't see any sign that they have been cut either (you CAN do that -- at your own risk!), but if they were cut, it was a pretty professional job, as all of the ends were ground square.


Before I removed the forks, I took sag measurements (check out Keith Code's video) on the front with the aid of a couple of zip ties positioned just above fork seals.  It was tough doing the measurement solo.  Because of this, I'm not positive that the measurement was dead on, because I got a sag percentage of about 15% which would be super stiff.  These springs are obviously aftermarket, I'm guessing much stiffer than stock looking at the other performance upgrades on the bike.  I'm going to roll the dice on this one and say that these springs are fine, and just go with a replenishment of 10w fork oil (proper spec).

Now as I'm about to dash out the door to get the fork oil, for some reason, something told me to wait.  Suddenly, all I could think of was the diluted wheel grease I noted on the left side of my wheel when I took it off.  A-HA!  I'll bet the crush washer at the bottom of the fork is probably leaking oil ever-so-slightly, which is working its way into the bearings.  Even if that's NOT it, I'd better get those bolts out of the bottom of the forks and Do It Right!  Fortunately I repacked the wheel grease at my last tire change, so I'm in good shape.

As I review my shop manual for the procedure to dismantle a Kayaba non-adjustable fork, it mentions use of the dreaded Triumph Factory Tool!  Here at Shadetree Motorsports, we hate the mention of the words 'Factory Tool'.  That means either: A) ponying up and buying the gold plated tool you need, or B) making the tool or a reasonable substitute that will harm neither you or the bike.

I get one of the bolts out by using a dowel with a handle (plastic of course) that was able to just hold the damping cylinder in place while I turned the bolt at the bottom.  I wasn't so lucky on the other one, so I figure this is a slow pitch for Street Cycles to have them get the other damping cylinder, it's just one bolt.  Sure enough though, they didn't have my $.76 crush washer in stock (7-10 days on Triumph parts!).  BUT, since I got the other bolt and washer pulled we matched a washer of the same inner diameter from a Suzuki -- perfect!  They quickly put the forks together, topped them off with oil and resealed them.

Here's the good part!  So I'm psyched, reinstalling the already serviced forks should be easy, kind of like filling your tire or adjusting your chain.  So, I slide the left fork into place, take my proper measurement from the top of the cap to the top of the yoke.  I insert the 6mm hex and begin to turn.  It turns strangely tight at first, followed by sudden looseness, then -- *SNAP!*  The bolt head snapped off the yoke leaving the threads inside the yoke!  DOH!!!  Looks like the yoke's going to have to come off so that the bolt can be drilled out in my drill press.  I'm possibly looking at a helicoil here.

Now coupled with this sudden obstacle, I have a Storz mounting bracket for handle bar risers that I cannot seem to get off so that I can pull the yoke!  The photo here is what is on my bike.  The allen bolts securing the bracket to the top of the yoke are apparently of some weird size: 6mm seems way too loose, 7mm is way too large, 5/16" seems like it should fit, because that's what the handlebar risers use.  But, even 1/4" is too large.  I manage to coax the Storz bolts out putting the 6mm hex bit into a thick, blue paper shop towel, then into the bolt head.  Somehow, it was just enough for me work them free.

I'm sure many will opine on their favorite way the top yoke off, which might mean removal of the stem and headset -- meaning, of course, the need to repack head bearings -- whatever.  It's not just a bolt off job on 1993 and up T309s, because there is a safety tab on the front of the frame which prevents removal of the top yoke by just lifting up after the 30mm retaining bolt is removed.  So, I decided that my best angle of attack was to remove the tank -- just two bolts here.  After I slid the tank off to the left and onto my bench, I could then turn the top yoke a full 90 degrees to the left, and past the safety tabs and lift the top yoke off the triple tree.

So, here I am with the yoke in my hand.  I decide it's time to just write the check on this one.  I do some business with Tammy and Nate Jones over at Custom Hawg in Scarborough, ME, and had been conversing with them via email about my predicament.  Tammy replied that I could bring the yoke over anytime and have Nate look at it.  That's what I will do.  Instead of taking the risk of knackering my 'unobtainium alloy' yoke, I'll give it to the guy who has probably looked down the barrels of many such scenarios in his day.  Not only did Nate totally set me up, he dropped what he was doing to do so!  I can't say that he will not be in the middle of project he can't break away from when YOU walk in, but it would be well worth your while!  In less than an hour, Nate was able to drill out the old bolt and chase the threads without a helicoil.  In fact, he took it to the next level and chased all of threads on the yoke because they looked a little beat!  Many thanks!

I left Custom Hawg with a smile on my face, and proceeded to tell them that I'm only 1.5 hours from putting it all back together -- they chuckled but said not a word!  I chuckled louder when I got home and looked at the rat's nest that was once a decent-looking bike.  1.5 hours?  Not a chance.  LOL!  I'm looking at probably twice that.  Oh, well, I don't have to be in Daytona for the conclusion of Bike Week or anything, so no big deal.  I'm going to take my time on reassembly, clean spots that haven't seen the light of day for 10-15 years, and Do It Right!

Friday, January 29, 2010

DIY Electrical Junction Box

Now more than ever our motorcycles' electrical systems are becoming taxed. Our ever increasing demand for the latest gear and gadgets such as a GPS, heated grips, heated gear, radar detector, cell phone chargers demands additional wires and connections, and by the time we've added the electric coffee mug warmer, it can look like a rat's nest beneath your seat and behind your headlamp. AND, if you never bothered to wire in a protective fuse, it can also create the potential risk for power surges and blown circuits. BUT, it doesn't have to be this way...

Today, we'll walk through the construction of an electrical junction box for your motorcycle. For about $20, this assembly will enable you to safely route and arrange your wires in an organized fashion, and protect them with an inline fuse. This setup will not only protect you from power surges, but will keep you from forgetting to turn all that "stuff" off and cooking your battery, because we wire this setup to be turned on and off with the key! The entire procedure will involve a trip to your local Radio Shack, and about an hour or so to actually do the work. So, go get the stuff, grab yourself a beer and get to work!!!

First let's start with tools required:
• #2 Philipps HD Screwdriver
• Wire cutter
• Wire stripper (carefully used pocket knife is ok)
• Wire crimper or sturdy pliers
• 2-liter plastic soda bottle (optional)

Now, the bill of materials:
• 8-post Dual-Row Barrier Block (distribution block)
• 8-post Position Jumper Cut in half
• Red and Black 18-gauge Wire
• Green 18-gauge Wire (opt., subst black)
• 5 Female Spade Connectors to crimp on
• 1 Male Spade Connectors to crimp on
• 2 Large U-shaped connectors to crimp on
• Several Small U-shaped connectors to crimp on
• 12V 30A Automotive Relay
• In-line fuse with 20A Fuse (not always included)
• Quick Connects to splice into wire
• Small Zip Ties
• Electrical Tape

Begin the project by taking a look at the wiring diagram posted here to get a feel for how everything will go together.

1. Strip the both ends of the lead wires from the inline fuse. Crimp one of the large U-shaped connectors around one end, this will go directly to the positive post on the battery. Crimp one of the female spade connectors around the other end. Plug this female spade connector onto the relay post marked #87.

2. Remove the Dual-Row Barrier Block from the packaging and loosen (do not remove) the screws.

Remove the 8-post jumper from the packaging and cut it in half. This is usually accomplished by bending the metal to and fro until it breaks. Lay the barrier block in front of you oriented left to right. Take one half of the jumper you just broke off and secure it beneath the 4 adjacent screws starting with the screw at the TOP LEFT. Now, take the other half of the jumper you just broke off and secure it beneath the 4 adjacent screws starting with the screw at the BOTTOM RIGHT. Refer to the wiring diagram for the correct orientation of the jumpers.

3. Cut a length of red wire about 12" long, and strip both ends. Your length of wire may vary depending on how far the relay is to be mounted from the block. Attach a female spade connector to one end, and plug it into the post marked #30 on the relay. To the other end, attach a small U-shaped connector, or twist the wire and solder it. Then attach this other end to the POSITIVE side of the block as indicated in the diagram.

4. Cut a length of black wire about 18" long, and strip both ends. Again, your length of wire may vary depending on how far the block is to be mounted from the battery. Crimp one of the large U-shaped connectors around one end, this will go directly to the NEGATIVE post on the battery. Crimp one of the small U-shaped connectors around the other end, or twist the wire and solder it. Then attach this small U-shaped connector to the NEGATIVE side of the block as indicated in the diagram.

5. Cut another length of black wire about 12" long, and strip both ends. Attach a female spade connector to one end, and plug it into the post marked #86 on the relay. To the other end, attach a small U-shaped connector, or twist the wire and solder it. Then, attach this other end to the NEGATIVE side of the block also, as indicated in the diagram.

6. Finally, we need to draw power from a switched power source. I tapped into the power to the taillight for my power source. And conveniently, the wire to the taillight of my 1995 Triumph Trident was a regular-sized female spade connector. Cut two lengths of green wire (or marked black wire), one about 18" long, the other 6" long and strip both ends of each wire. To the 18" piece, attach a female spade connector to one end, and plug it into the post marked #85 on the relay. Take the other end of the 18" piece and twist one of the stripped ends of the 6" piece onto it. Now crimp a male spade connector onto the two wires you just twisted together.

Unplug the switched power source (or splice into the line). Here, it was the regular-sized female spade connector connected to the taillight. I had to remove my taillight to accomplish this part. Attach a female spade connector to the other end of the 6" piece of green wire, and plug it into the taillight. Take the male spade connector attached to the two green wires you just twisted together, and plug it into the connector you just unplugged from the taillight.

Voila! You now have switchable power. All you need to do now to add accessories is to take your positive and negative leads from the accessory, crimp small U-shaped connectors to them (or solder the ends), and attach them to the appropriate sides of the block. To better discern positive from negative leads, I went the extra step of marking the screws on the positive side of the block with a red Sharpie, and those on the negative side with a black Sharpie.

I have access to thin flexible plastic sheet stock as well. I used this to fold a protective layer above and beneath the junction box to protect the connections from possibly shorting out. The edges are open in order to route the wires. As a substitute, I would cut a rectangular section out from a plastic soda bottle measuring 4" x 10". Fold it in half so it becomes two 4" x 5" sections. Use this as a sheath for the box, and tuck the edges away from the fold under the igniter box.

I took it for a test run just the other day, and it works great! Everything switches on and off just as it should, and no more worrying about dead batteries!